News - Hydroforming.net Search - Hydroforming.net Industry - Hydroforming.net Forum - Hydroforming.net Subscription - Hydroforming.net Careers - Hydroforming.net Schedule - Hydroforming.net Home - Hydroforming.net
Hydroforming.net   german
back             All rights reserved. © Hydroforming.net by Boerries Burkhardt .
   

Hydroforming.net News

Contacts:
Verson Pressentechnik GmbH
Am Heller 1
D-57250 Netphen-Werthenbach
Germany

phone: +49 (02737) 989-500
fax: +49 (02737) 989-290
e-mail: Versonpt@aol.com
contact: Dietmar Kölsch

Hydroforming Press Verson GHFP 1.500

Invitation for a Pressdemonstration by VERSON Pressentechnik

During the opening ceremony of VERSON Pressentechnik's Communication Center on September 15, 1999 one could see a Hydroforming Press developed by GRÄBENER Maschinentechnik and VERSON.
All assembly and commissioning works has been done.
Since January 2000 several customers tested this press by using their own tools.
Based on secrecy agreements, which didn't allow to show these tools and parts, Gräbener build a tool for T - parts with a diameter of 88,9 mm. This die shows all functions of the press. The actual cycle time of this part with a wall - thickness of 3,2 mm is 19 seconds.

This press can bee seen in production until April 30, 2000 at Gräbener's premisses. Arrangements for demonstrations of the Hydroforming Press can be done with Mr. Kölsch or Mrs. Hoffmann under Telephone + 49 (0) 2737 / 989 - 500 or E-mail address Versonpt@aol.com .

Targets of Development of the Control and Press

Control

  • Open Control Concept
  • PC only for Programming and Visualization
  • Easy Programming of parts
  • Operating System Microsoft Windows / NT
  • Use of Satandard Components
  • Decentralized Peripheries ( FlexIO / ET )
  • Use of all PLC Controls with Profibus
  • Axis Controller Cycletime 2 ms
  • Axis Controller usable for Hydraulic and Electric Drives

Hydraulic

  • Modular Design
  • Global Use of Standard Components
  • Water Hydraulic and EmulsionSystem
  • Standard Components
  • Modular Rough - and Fine Filter System
  • Pumpfilter Circulation System in the complete Emulsiontank
  • Oilseparation in Auxillary Stream
  • No additional Swamptanks
  • Easy Change of Seals in the High Pressure Intensifier
  • No Prestressed Tie - rod Connections in the High Pressure Intensifier

Press

  • Complete FEM Calculation of all Press Sizes
  • Homogeneous Stressdistribution
  • Minimal Deflections
  • Consideration of Tool Specific Loads
  • Design of Standard Sizes

Following some technical details of the realized Hydroforming Press:

Type: GHFP 1.500

  • Closing Force at 260 bar 15.000 kN
  • Number of Closing Cylinders 2
  • Table Size 3.100 x 2.500 mm
  • Stroke of Slide 1.000 mm
  • Max. Toolweight 25 tons
  • Closing Speed of Slide
  • ( Digital Controled Axis ) 650 mm / sec.
  • Installed Capacity incl. Waterhydraulic 320 kW
  • High Pressure Intensifier Volume 4,8 l / 4000 bar
  • CNC Control with 5 digital controlled Axis

Hydroforming.net News File "eng040100.htm"

   

Top


Last update: April 02, 2000
Letzte Änderung: 02 April 2000

Contact Hydroforming.net

This technical information are distributed by Verson / Gräbener Hydroforming .
Hydroforming.net is not responsible for the information and truth of this report.

Copyright © 1998-2000 Hydroforming.net by Boerries Burkhardt.
All rights reserved.